High Molecular Weight Cationic Acrylamide Co-Polymer Flocculant – 4537

Available in 25Kg drums

200Kg and IBC orders are POA

Description

Accepta 4537 is a high performance; high molecular weight cationic acrylamide co-polymer based flocculant in an aqueous dispersion. It is especially useful in those applications where phase separation takes place by floatation.

Accepta 4537 has an excellent environmental profile. It is free of surfactants and organic solvents, with a very low volatile organic compound (VOC) content.

Its manufacturing process has a low environmental impact, compared with many other manufacturing processes for flocculant products.

Accepta 4537 utilises the most advanced technology in terms of its environmental impact.

Accepta 4537 can work alone or can be combined with other common products used in water treatments as: aluminium chloride, aluminium polychloride, ferric chloride, polyamine, lime, etc. Under such circumstances if an anionic flocculant is used during the final stages a more complete and effective flocculation (dual treatment) can be achieved.

Accepta 4537 is a versatile cationic acrylamide and can be used across a wide range of applications. It provides excellent results in sludge dewatering processes, in belt filters and centrifuges.

In belt filters the product helps to keep clean the belts in situations where the sludge contains hydrocarbons or hydrophobic compounds.

Accepta 4537 is effective across a wide pH range, it is also easy to handle, and dissolves readily in use.

Product Benefits

  • High performance high molecular weight cationic acrylamide co-polymer
  • Highly versatile, can be used across a wide range of applications
  • Good where phase separation takes place by floatation
  • Excellent environmental profile
  • Can be used alone or with other treatment formulations
  • Effective across a wide pH range
  • Easy to handle, and dissolves readily

Product Properties

Form: Cationic acrylamide copolymer in aqueous dispersion
Appearance: White milky liquid
Density: 1.2 g/cm³
pH: 3.0 – 4.1
Viscosity: 25-500 cp
Viscosity (at %): 1.0 15-30 cp
Ionic Character: Cationic
Ionicity: Low
Molecular weight: High

*Full details of the product properties are available in the Safety Data Sheet. See below.

Application & Dosage Information

In most of cases Accepta 4537 must be dissolved in water prior its use in the application. Its dissolution is very fast if the procedure conditions are adequate.

For an effective and rapid dissolution process it is important to get a good first contact between the product and water. We recommend pouring Accepta 4537 slowly over strongly agitated water. A small dose of product should contact water on the vortex formed by the agitation.

Continue to thoroughly mix until all the product has been fed into the water, after that the agitation rate may be reduced till the dissolution is complete.

The low viscosity of Accepta 4537 allows its dosage rate to be easy controlled. It is however, very important to avoid any incoming water in the dosing system of the raw product, for this reason we recommend using non-return valves. If it does happen pumps and tubing could become blocked.

We also recommend dissolutions of the product at concentrations above 5 % are not used. High concentrations are harder to homogenize and handle because of the high viscosities obtained.

Solution stability depends on several factors: quality of the dilution water (hardness, conductivity, and pH), temperature, concentration, etc. We recommended using any prepared dissolution within a few hours after its preparation.

When a loss of viscosity is observed it usually means that the prepared solution has degraded. If this occurs the dissolution is still useful, though the dosage necessary to maintain product performance may be higher.

As Accepta 4537 can be dissolved easily, in some specific cases, it may be dosed to the application without previous dissolution.

It is always advisable to carry out a ‘Control Of Substances Hazardous to Health’ (COSHH) assessment before use.

Safety, Storage & Handling

For full details concerning safety precautions, storage and handling procedures for this product please refer to the latest Safety Data Sheet. To request the latest MSDS for this product please fill out the form below.






Additional information

Weight 25 kg